Directed Electronics 381 Series Guia de Instalação descarregar pdf (Página 20)

FEATURE DESCRIPTIONS

The features of the system are described below. If the system is being programmed with a DEI Bitwriter or

996T and a personal computer the options available may change. PC programmable options are indicated by

the computer icon shown at the left.

Menu #1- Basic Features

1-1 ACTIVE/PASSIVE ARMING:

When active arming is selected, the system will only arm when the trans-

mitter is used. When set to passive, the system will arm automatically 30 seconds after the last door is closed.

To alert the consumer of passive arming, the siren will chirp 20 seconds after the door is closed. This provides

the consumer with an audible warning prior to the system actually arming. At the 30 second mark, the system

will arm, but the siren will not chirp.

1-2 AUDIBLE ARM/DISARM CONFIRMATION ON/OFF:

This feature controls the chirps or voice messages

(if using the 516M) that confirm the arming and disarming of the system.

1-3 IGNITION CONTROLLED DOOR LOCKS ON/OFF:

When turned on, the doors will lock three seconds

after the ignition is turned on and unlock when the ignition is turned off. Ignition controlled door locks can be

further programmed in Feature 2-8. Also, if using the BLACK/WHITE ignition lock safety input (H3/10), the sys-

tem will not lock the doors until ground is removed from the wire.

The TechSoft Programmer or the 998T

Bitwriter will display separate steps for ignition lock and ignition unlock. They can be programmed on or

off independently.

1-4 ACTIVE/PASSIVE LOCKING:

If passive arming is selected in Feature 1-1, then the system can be pro-

grammed to either lock the doors when passive arming occurs, or only lock the doors when the system is

armed via the transmitter. Active locking means the system will not lock the doors when it passively arms.

Passive locking means that the system will lock the doors when it passively arms.

NOTE: Remember, when passive arming is selected, the unit will chirp 20 seconds after the last door

is closed.The system does not actually arm or lock the doors until 30 seconds after the door is closed.

1-5 PANIC WITH IGNITION ON:

This feature controls whether or not the panic mode is available with the igni-

tion on. In some states, there are laws prohibiting a siren sounding in a moving vehicle. This feature allows the

system compliant with these regulations.

1-6 DOOR LOCK PULSE DURATlON:

Some European vehicles, such as Mercedes-Benz and Audi, require

longer lock and unlock pulses to operate the vacuum pump

Programming the system to provide 3.5 second

pulses, will accommodate the door lock interface in these vehicles. The default setting is 0.8 second door lock

pulses. Some modification to the door lock harness (H2) is also necessary. See

“Mercedes-Benz and Audi -

1985 and Newer (Type E) “

diagram.

1-7 FORCED PASSIVE ARMING ON/OFF:

To use this feature. Passive arming must be selected in Feature

1-1. When turned on, forced passive arming will ensure that the system will passively arm, even if a zone is

left open or invalid. Forced passive arming occurs one hour after the ignition is turned off.

1-8 AUTOMATIC ENGINE DISABLE (AED) ON/OFF:

AED is a full-time, passive starter disable that works

independently of the security system. When turned on, the orange, ground-when-armed output (H1/1) will go

active 30 seconds after the ignition is turned off. The LED will flash at half its normal rate when the ignition is

turned off to indicate that AED is active and will interrupt the starter in 30 seconds. AED does not occur in

Valet

mode and can be bypassed using the emergency override procedure. The transmitter can be used to

disarm AED; however, the system must be armed and then disarmed using the transmitter, in order to disarm

AED.

1-9 ARMED WHILE DRIVING/VEHICLE RECOVERY SYSTEM:

In the default setting (Armed While

Driving), the system can be armed with the ignition on. When armed, the ground-when-armed is not

active and the sensors are bypassed. The door triggers will remain active. If programmed to the Vehicle

Recovery System (VRS

) setting, VRS will be activated.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Comentários a estes Manuais

Sem comentários

Directed Electronics 381 Series Guia de Instalação Página 20

Comentários a estes Manuais

Manuais e produtos relacionados com Alarmes para automóveis Directed Electronics 381 Series