Directed Electronics VS102 Especificações descarregar pdf (Página 23)

A-15

A LAUER driver

Status indicators The PCS 830.3/31 features a 7-segment „ST.x“ display which informs

about the state of the channel.

The following display states are currently possible:

„0“ programmable controller is set to „STOP“, i.e. the PCS 830.3/31 waits

for the „RUN“ signal and/or for the outputs to be enabled. This display

is simultaneously shown for all three channels.

„1“ The corresponding channel waits for the complete reception of the

cross-reference list. This channel was not parameterized correctly,

or the address (6-segment DIL) was incorrectly set, or the first three

words of the cross-reference data block have been incorrectly set if

this display does not extinguish.

„2“ (flashing). The corresponding channel is set to the DIAG diagnosis

function. The cross-reference list was correctly received. This function

is only possible along with the CL300 and CL500 and the examples

contained on the floppy disk.

„7“ TIMEOUT fault - time infringement of the corresponding channel.

Interruption of the communication between the PCS 830.3/31 and

the PCS operating console. Possible fault conditions:

PCS operating console: „TIMEOUT“

Cause: Cable break or the handling block has not been processed

for sometimes.

Remedy: Check the cabling and select the handling block cyclically.

Extend the timeout time of the operating console if possible. PCS

operating console: „CONNECT(ION)“ or „TOO MANY

REPETITIONS“.

Cause: The operating console has received multiple times wrong

data (following another).

Remedy: Checking the noise suppression measures and increase

the WDHA if possible.

„8“ CONNECT fault, i.e. the corresponding channel of the PCS 830.3

has received multiple times wrong data (following another) (the PCS

operating console shows „TIMEOUT“). In this case, noise

suppression measures are to be explored and/or to be improved if

necessary!

„9“ WATCHDOG fault, i.e. either the PCS 830.3/31 board is located in a

very noisy environment, or it is defective (communication cannot be

restarted). If at all, this display appears for all channels simultaneously.

„-“ The corresponding channel has either sent or received a repeat

request. With a reparabel fault, the „-“ extinguishes subsequently

again. If the fault was not reparabel, a „7“ (TIMEOUT) or „8“

(CONNECT) is subse-quently displayed. Constant flickering of this

segment informs about a very noisy environment.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 87 88

Comentários a estes Manuais

Sem comentários

Modelle	Dokumententyp
CONTROL2 BX600	Bedienungsanleitung Fujitsu CONTROL2 BX600 User's Manual, 46 Seiten
FS-1004MT	Bedienungsanleitung Fujitsu FS-1004MT User's Manual, 27 Seiten
FS-1004MU	Bedienungsanleitung Fujitsu FS-1004MU User's Manual, 32 Seiten
FS-102AT	Bedienungsanleitung Fujitsu FS-102AT User's Manual, 3 Seiten
FS-102ATL	Bedienungsanleitung Fujitsu FS-102ATL User's Manual, 23 Seiten
FS-1104AU/1104MU	Bedienungsanleitung Fujitsu FS-1104AU/1104MU User's Manual, 60 Seiten
S26361-F2293-L602	Datenblatt Fujitsu s2-1602, 4 Seiten

Directed Electronics VS102 Especificações Página 23

Comentários a estes Manuais

Fujitsu KVM-Schalter Benutzerhandbücher

Directed Electronics VS102 Especificações Página 23

Comentários a estes Manuais

Manuais e produtos relacionados com não Directed Electronics VS102

Fujitsu KVM-Schalter Benutzerhandbücher