Directed Electronics READY REMOTE 24923 Guia de Instalação

2244992233➤OOwwnneerr’’ss//IInnssttaallllaattiioonn GGuuiiddee

6© 2006 Directed Electronicsto assure that the system does not unintentionallyremote start the vehicle.4. THE USER MUST INSTALL A CARBONMONOXIDE DETEC

7© 2006 Directed Electronicsremote start unit has not been properly installed. The remotestart module must be removed or properly reinstalled so thatt

8© 2006 Directed Electronicsmmaaiinn hhaarrnneessss ((HH11)),, 88--ppiinn ccoonnnneeccttoorr________________________Use the following wiring guide

9© 2006 Directed Electronicssseeccoonnddaarryy hhaarrnneessss ((HH22)),, 77--ppiinn ccoonnnneeccttoorr_____________________rreellaayy hheeaavvyy

10© 2006 Directed Electronicsuussiinngg LLEEDD tteesstt pprroobbeeTo use the LED test probe:1. Remove the protective cover off the probe tip. Save

11© 2006 Directed ElectronicsiinnssttaallllaattiioonnBe sure to read this section thoroughly and view the Do-It-Yourself Installation CDROM video in i

12© 2006 Directed Electronicswwiirriinngg qquuiicckk rreeffeerreennccee gguuiiddeeVIOLET/BLACK - Lock #87 Normally Open Input 15A FusedBROWN/BLACK

13© 2006 Directed Electronicsstep 1Ground WireThe BLACK (H1/5) wire on the main 8-pin harness is ground.First strip back a ¾-inch section of the insul

14© 2006 Directed Electronicsstep 2Constant Power and Ignition wiresAlmost all power and ignition wires can be found behind the keycylinder under the

15© 2006 Directed Electronicsthe kick panel area and secure it. Probe one of the thicker gaugewires. The color and identity of your specific vehicle w

16© 2006 Directed Electronicsconstant (+)12 volts. Locate the suspected wire using thewww.designtech-intl.com Web site and place the red lead of thete

17© 2006 Directed Electronicsstep 3Accessory and Starter wiresThe starter and accessory wires will be located in the same harnessas the ignition and c

18© 2006 Directed Electronicsinsulation off a small portion and solder the thick ORANGE (3)wire of the heavy gauge wire and wrap it with electrical ta

19© 2006 Directed Electronicswire. With the key in the off position the LED tester should beextinguished in all key positions except the crank positio

20© 2006 Directed Electronicsstep 4Safety Shutdown WiresWith all ignition wires properly connected, find the appropriatesafety shutdown wires. These a

21© 2006 Directed Electronicswire color according to the web information. With your blacktest probe lead still in the kick panel, probe the suspected

22© 2006 Directed ElectronicsPlace the wire with the spade connector onto the pin switch andrun the wire into the vehicle’s passenger compartment thro

23© 2006 Directed Electronicsstep 5Parking light flashThere are several different types of parking light circuits. Thefollowing description is for a s

24© 2006 Directed ElectronicsUsing the web information on the vehicle, locate the suspectedwire and place the red lead of the test probe to a constant

25© 2006 Directed Electronics

i© 2006 Directed Electronicslliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyyDirected Electronics, Inc. (hereinafter "Directed

26© 2006 Directed Electronicsstep 6Door LocksThe system comes with a built in relay pack for door lock oper-ation. When attempting to interface the po

27© 2006 Directed Electronicsinstallation by locating the same wires in the vehicle’s kick panel.If no central locking switch is found, the installati

28© 2006 Directed Electronicsmust have a vacuum actuator in each door. Make sure that lock-ing the doors from the driver's or passenger side usin

29© 2006 Directed Electronicsdirectly to the lock motors.type A: positive-triggered, relay-driven systemH2/2H2/3H2/4H2/5H2/6H2/7LOCKRELAYUNLOCKRELAY#8

30© 2006 Directed Electronicstype B: negative-triggered, relay-driven systemThis system is common in many Toyota, Nissan, Honda, andSaturn models, as

31© 2006 Directed Electronicstype C: direct-wired, reversing-polarity systemtesting reversing polarity systemsUse these instructions if the power door

32© 2006 Directed ElectronicsIt is critical to identify the proper wires and locate the masterswitch to interface properly. Locate wires that show vol

33© 2006 Directed Electronics HH22//44 VVIIOOLLEETT//BBLLAACCKK::This wire must be connected toa constant (+)12 volts. The best connection point for

34© 2006 Directed Electronicstype D: adding one or more after-market actuatorsVehicles without factory power door locks require the installa-tion of o

35© 2006 Directed Electronicstype E: electrically-activated vacuumThis system is found in Mercedes-Benz and Audi 1985 andnewer. The door locks are con

ii© 2006 Directed ElectronicsOR IN CONNECTION WITH THE INSTALLATION, USE, IMPROPER USE, ORINABILITY TO USE, THE PRODUCT, EVEN IF THE PARTY HAS BEENADV

36© 2006 Directed Electronicstype F: one-wire system (cut to lock, ground to unlock)This type of door lock system usually requires a negative pulseto

37© 2006 Directed Electronicstype G: positive (+) multiplexThis system is most commonly found in Ford, Mazda, Chryslerand GM vehicles. The door lock s

38© 2006 Directed Electronicspower wire, or the (+) terminal of the battery.3. Operate the door lock switch/key cylinder in both directions todetermin

39© 2006 Directed ElectronicsTTWWOO--RREESSIISSTTOORR TTYYPPEE::If two resistors are used in the factorydoor lock switch/key cylinder, the door lock

40© 2006 Directed Electronicsstep 7Engine monitoring (voltage—default setting)—optionalDuring remote start the system will need to know if the enginei

41© 2006 Directed ElectronicsOn some vehicles the electrical system has too low of a voltagevariance for the remote start module to see. In this case

42© 2006 Directed ElectronicsPlace the black lead of the multi-meter on the negative batterypost and secure it. Put the multi-meter in the AC position

43© 2006 Directed ElectronicsSince most newer vehicles come equipped with a factory alarmsystem, it is sometimes necessary for the factory alarm to be

44© 2006 Directed Electronicsstep 9Immobilizer Bypass ModulesMost newer vehicles have a factory engine immobilizer systemdesigned to prevent any unaut

45© 2006 Directed ElectronicsTo determine what bypass module your vehicle requires, use thewww.designtech-intl.com web-site in the Interface Module Lo

1© 2006 Directed Electronicsttaabbllee ooff ccoonntteennttsslliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy.. .. .. .. ..

46© 2006 Directed Electronics3.PPrrooggrraamm..Within 10-seconds, press and hold thebutton on the transmitter, until the parking lights turn offand th

47© 2006 Directed Electronicsstep 11Testing the systemOnce steps 1-10 have been completed, the operation of thesystem can be tested.Ensure that the tw

48© 2006 Directed Electronicsrreemmoottee ffuunnccttiioonnssThe receiver uses a computer-based learn routine to learn theremote buttons.standard conf

49© 2006 Directed ElectronicsButtonPress the button to unlock the vehicle.ButtonPress the button twice to remote start the vehicle.ButtonPress the

50© 2006 Directed Electronicsccoonnttrrooll mmoodduullee pprrooggrraammmmiinnggDependent on the vehicle, use the following data with theinstructions

51© 2006 Directed ElectronicsIIggnniittiioonn CCoonnttrroolllleedd DDoooorr LLoocckkss OOnn//OOffff ((RREEDD)) - When on, thedoors will lock thr

52© 2006 Directed Electronicsduring normal driving. If it finds a valid tachometer signal themodule will use tachometer mode, otherwise the module wil

53© 2006 Directed Electronicsuussiinngg yyoouurr ssyysstteemmwarning! safety firstThe following safety warnings must be observed at all times: When

54© 2006 Directed Electronicsmust not remotely start while the car is in gear. This testingshould be performed by an authorized Directed Electronics,

55© 2006 Directed Electronicslocking with remoteTo lock the doors press for one second. The doors will lockand the parking lights will flash once to

2© 2006 Directed Electronics

56© 2006 Directed ElectronicsWhen you are ready to drive the vehicle: 1. Insert the ignition key and turn it to theON (not the START) positio

57© 2006 Directed Electronicstimer modeThis feature allows you to remotely start and run your vehicle for12-minutes every 3 hours (for a maximum of 6

58© 2006 Directed Electronics The shutdown toggle switch is put into the ON position. Note: The button on the remote can be pressed twiceat any tim

59© 2006 Directed ElectronicsUse the following procedure to exit Pit Stop Mode:1. Enter the vehicle.2. Place the key into the run (not the crank or st

60© 2006 Directed Electronicsttrroouubblleesshhoooottiinngg➤TThhee iiggnniittiioonn ccoommeess oonn,, bbuutt tthhee ssttaarrtteerr wwiillll nn

61© 2006 Directed Electronics➤TThhee cclliimmaattee ccoonnttrrooll ssyysstteemm ddooeess nnoott wwoorrkk wwhhiillee tthhee uunniitt iissoopp

62© 2006 Directed Electronicslocks" are not recommended for any high current heavygauge wiring. Also, if the vehicle has more than one 12-volt in

63© 2006 Directed Electronicsnnootteess_______________________________________________________________________________________________________________

64© 2006 Directed Electronics

65© 2006 Directed ElectronicsQUICK REFERENCE GUIDE:To lock the doors using your remote Pressing for one second will lock the doors. The doors will l

3© 2006 Directed Electronicswwhhaatt iiss iinncclluuddeedd➤ Control Module➤ One 4-Button Remote➤ 8-Pin Main H1 Harness➤ 7-Pin H2 Secondary Harness➤

The company behind this system is Directed ElectronicsSince its inception, Directed Electronics has had one purpose, to provide consumers withthe fine

4© 2006 Directed Electronicsiimmppoorrttaanntt iinnffoorrmmaattiioonnCongratulations on the purchase of your remote start keylessentry system. This s

5© 2006 Directed Electronicsfcc/id noticeThis device complies with Part 15 of FCC rules. Operation issubject to the following conditions: (1) This dev