Directed Electronics AutoCommand 28624TN Guia de Instalação

MMooddeell 2288662244TTNN➤OOwwnneerr’’ss//IInnssttaallllaattiioonn GGuuiiddeeOEM Series

7© 2006 Directed ElectronicsWiring Quick Reference GuideHeavy GaugeWiresBLUEWHITE (+)YELLOWPINKPINKGREEN (+) output to ign/acc2 circuitYELLOW/RED (-)

8© 2006 Directed ElectronicsH1 Harness - 6 pin connector__________________Pin # Color NoteH1/1YellowSelectable positive or negative parking light outp

9© 2006 Directed ElectronicsH2 Harness - 8 pin connector________________________Pin # Color NoteH2/1GreenUse this wire if the vehicle fails to start c

10© 2006 Directed ElectronicsH3 harness - 3 pin connector_________relay heavy gauge wires__________________BLACK (-) groundYELLOW (+) starter outputPI

11© 2006 Directed ElectronicsInstallation OverviewBe sure to read this section thoroughly in its entirety before start-ing the installation. Pay speci

12© 2006 Directed ElectronicsGround WireThe BLACK wire connects to the pin next to the light flash jumperfuse. First strip back a ¾-inch section of t

13© 2006 Directed ElectronicsOnce the lower dash panel has been removed, locate the ignitionharness at the back of the key cylinder. This is usually a

14© 2006 Directed ElectronicsWith the key in the off position, test the suspect wire. Theconstant power wire will read 12V on the multimeter. Once th

15© 2006 Directed ElectronicsIf your vehicle requires more than two ignitions, an additionalrelay (not provided) is required. Refer to the diagram bel

16© 2006 Directed ElectronicsAccessory and Starter wiresThe starter and accessory wires will be located in the same harnessas the ignition and constan

i© 2006 Directed Electronicslliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyyDirected Electronics (hereinafter "Directed"

17© 2006 Directed ElectronicsIf the GREEN wire is being used for ign2 an additional relay (notprovided) is required for a 2nd accessory. Refer to the

18© 2006 Directed ElectronicsMany Nissan and late-model Chrysler vehicles have two starterwires. A relay and/or resistor (not provided) is required to

19© 2006 Directed ElectronicsStep 2, H1, Main Harness ConnectionsFactory Alarm DisarmSince many newer vehicles come equipped with a factory alarm itis

20© 2006 Directed ElectronicsParking light flashThere are several different types of parking light circuits. Thefollowing description is for a standar

21© 2006 Directed ElectronicsSafety Shutdown WiresWith all ignition wires properly connected, find the appropriatesafety shutdown wires. These are the

22© 2006 Directed ElectronicsUsing a sharp, pointed object poke a hole into the grommet(being careful not to damage any existing wires in the grommet)

23© 2006 Directed ElectronicsStep 3, H3 Door Lock ConnectionsThere are 8 different types of door lock systems (Type A - H).Refer to the vehicle-specif

24© 2006 Directed ElectronicsAll other door lock systems will require additional relays and/orresistors. A Directed Electronics 451M Doorlock module

25© 2006 Directed ElectronicsStep 4, H2 HarnessEngine Monitoring ExplainedDuring remote start the system will need to know if the engine isrunning. Th

26© 2006 Directed ElectronicsTachometer WireIdentify the suspected tach wire according to the web informa-tion. Next, place the black lead of a MULTI

ii© 2006 Directed ElectronicsOR IN CONNECTION WITH THE INSTALLATION, USE, IMPROPER USE, ORINABILITY TO USE, THE PRODUCT, EVEN IF THE PARTY HAS BEENADV

27© 2006 Directed Electronicsof insulation off the tachometer wire in the vehicle and solder thegreen tachometer input wire to it. Then wrap the conn

28© 2006 Directed ElectronicsFollowing is a brief description of the remainder of the wires inthe H2 harness. For specific details on connecting these

29© 2006 Directed Electronicsoutput. The output will then remain on until the transmitterbutton is released. Retained Accessory, Dome Light or Starter

30© 2006 Directed ElectronicsHeadlight Control wireThe Yellow/Brown wire provides an output for activating thevehicle headlight circuit. It is control

31© 2006 Directed ElectronicsStep 5, Mounting the Receiver/AntennaReceiver/antenna position should be discussed with the vehicleowner prior to install

32© 2006 Directed Electronics

33© 2006 Directed ElectronicsStep 6, Immobilizer Bypass ModulesMost newer vehicles have a factory engine immobilizer systemdesigned to prevent any una

34© 2006 Directed ElectronicsStep 7, ProgrammingProgramming transmittersYour system can learn up to 4 transmitters. The following proce-dure will sho

35© 2006 Directed ElectronicsYou can learn more than one transmitter function at a time byadvancing to another transmitter learn Step. To do this, fir

36© 2006 Directed ElectronicsTransmitter Button Programming ChartTransmitter Button Auto-LearnRemote Start/StopCarFinder & Disarm/Trunk PopHead Li

1© 2006 Directed Electronicsttaabbllee ooff ccoonntteennttsslliimmiitteedd lliiffeettiimmee ccoonnssuummeerr wwaarrrraannttyy.. .. .. .. ..

37© 2006 Directed ElectronicsProgramming System SettingsMany of the features and operations of this system can bechanged to suit most of today's

38© 2006 Directed Electronicsoptiona. Option 1: Press the transmitter button assigned tothe Remote Start function (usually the button) toset factory

39© 2006 Directed ElectronicsExiting Feature programming: The following will cause the system to exit programming and isindicated by 5 short chirps of

40© 2006 Directed ElectronicsFeature Menu 1 Descriptions1. Engine Monitoring: Defines how the engine is monitored whilethe Remote Start is active.1. N

41© 2006 Directed Electronics5. Wait-To-Start: This chooses the method of Starter output delayfor Diesel engines.1. Diesel Input wire: An input on the

42© 2006 Directed Electronics1. Horn: The output will be pulsed during full trigger events2. Siren: The output will be constant during full triggereve

43© 2006 Directed ElectronicsFeature Menu 2 Chart Feature Menu 2 Descriptions1. Arming Type: Selects if the alarm will arm by one or both avail-able m

44© 2006 Directed Electronics2. Passive: The doors will lock when armed via transmitter,Passive Arming and Auto Re-arming.3. Ignition Locking: Select

45© 2006 Directed Electronics7. Lock Duration: Selects the duration of the pulses when Lockingand Unlocking the doors.1. Short pulse: The Door Lock &

46© 2006 Directed Electronics11. Acc pulse/DomeLight/ Starter Kill-Anti-grind: This controlsthe output of the "Brown" output wire.1. Acces

2© 2006 Directed Electronics

47© 2006 Directed ElectronicsSystem DiagnosticsAlarm diagnosticsWhen arming or disarming the alarm, this system will alert you ofalarm triggers or act

48© 2006 Directed ElectronicsAlarm Input ChartLED Flashes Input Description1The 'Gray/Blk' Input wire2The 'Orange' Brake Input wir

49© 2006 Directed ElectronicsRemote Start DiagnosticsRemote Start Diagnostics:Remote Start diagnostics are an important tool that will diag-nose the s

50© 2006 Directed ElectronicsLast Start Diagnostics:The system holds in memory the reason for the most recentremote start activation. This diagnostic

51© 2006 Directed ElectronicsShut Down Diagnostics:The system holds in memory the reason for the most recentremote start shut down. This diagnostic re

52© 2006 Directed ElectronicsTesting the systemOnce steps 1-7 have been completed, the operation of the systemcan be tested.Ensure that the two 30-amp

53© 2006 Directed ElectronicsNeutral Safety TestSome vehicles do not have an electrical neutral safety switch.Instead, a mechanical neutral safety swi

54© 2006 Directed Electronics4. Turn the key to the "run" position, this will release theshifter.5. Place the shifter in the drive position.

55© 2006 Directed ElectronicsTroubleshootingThe ignition comes on, but the starter will not crank.Does it start with the key in the ignition? If so, d

56© 2006 Directed ElectronicsCheck to ensure that the hood is not open and that the brakepedal is not depressed. Check harnesses and connections. Mak

3© 2006 Directed ElectronicsInstall Guidewhat is includedControl Module6-Pin Main H1 Harness8-Pin H2 Secondary HarnessHeavy Gauge WiresAntenna and cab

57© 2006 Directed ElectronicsMMooddeell 2288662244TTNN➤OOwwnneerr’’ss GGuuiiddee

58© 2006 Directed ElectronicsOwner’s GuideNow that the installation is complete and tested, it is time tolearn about the many outstanding remote start

59© 2006 Directed Electronics➤Trunk pop output will disarm your alarm and open thetrunk as you approach your vehicle➤Headlight output can operate as d

60© 2006 Directed ElectronicsOPERATING YOUR SYSTEMS FEATURESThe Remote Start, Alarm and Convenience features described inthis section follow the trans

61© 2006 Directed ElectronicsWhen you are ready to drive the vehicle:➤Insert the ignition key and turn it to the ON (not theSTART) position.➤Press the

62© 2006 Directed Electronics➤ The user steps on the brake as they begin to drive thevehicleSafety shut down inputs:While the vehicle is running durin

63© 2006 Directed Electronics➤The Horn/Siren will chirp once and the lights will beginflashing to indicate Quick Stop Mode is active.➤Turn the ignitio

64© 2006 Directed ElectronicsTo de-activate Daily Start:➤Press and hold the & buttons on your trans-mitter for more than 3 seconds➤Activate Vaca

65© 2006 Directed ElectronicsTo de-activate Vacation Mode:➤Press and hold the & buttons on your trans-mitter for more than 3 seconds➤Activate Da

66© 2006 Directed ElectronicsAlarm and Security FeaturesTransmitter Arming of the AlarmYou can arm the system by pressing the button of your trans-mi

4© 2006 Directed Electronicsimportant informationCongratulations on the purchase of your remote start keyless entrysystem. This system will allow conv

67© 2006 Directed ElectronicsAuto-rearming featureAuto-rearming is designed to protect the vehicle in case of unin-tended disarming of the alarm. It w

68© 2006 Directed ElectronicsTransmitter Disarming the AlarmTo disarm the security system, press the button of the trans-mitter. When the system disa

69© 2006 Directed ElectronicsTo active Panic Mode: ➤Press and hold the button on the transmitter for 6seconds➤The Horn/Siren output and light flash w

70© 2006 Directed ElectronicsValet ModeValet Mode will defeat the alarm trigger and remote start opera-tions while leaving all other security and conv

71© 2006 Directed ElectronicsConvenience FeaturesCarfinder FeatureThis feature allows you easily locate you vehicle in large and dark-ened parking are

72© 2006 Directed Electronics➤Press and hold for 3 seconds the button on thetransmitter and then release it.➤The headlight output toggle on/off accor

73© 2006 Directed ElectronicsGlossary of termsControl Module:The “brain” of your system. Usually hidden underthe dash area of the vehicle. It houses t

74© 2006 Directed ElectronicsNNootteess_______________________________________________________________________________________________________________

75© 2006 Directed ElectronicsQUICK REFERENCE GUIDE:Alarm Operation To Arm and Lock: Press the button for one second. The doors will lock andthe park

The company behind this system is Directed ElectronicsSince its inception, Directed Electronics has had one purpose, to provide consumers withthe fine

5© 2006 Directed Electronicsfcc/id noticeThis device complies with Part 15 of FCC rules. Operation issubject to the following conditions: (1) This dev

6© 2006 Directed ElectronicsTO THE VEHICLE. ALL DOORS LEADING FROM ADJACENTLIVING AREAS TO THE ENCLOSED OR PARTIALLYENCLOSED VEHICLE STORAGE AREA MUST